膜結構充電樁車棚的安裝可以使充電樁避免了日曬雨淋，延長了它的使用壽命，另外膜結構停車棚還能為人們帶來便利，瓢潑大雨、烈日暴曬時，雨棚恰好為車子提供了一處臨時安身之所。今天，小編就為大家介紹一下充電樁車棚的安裝步驟及其注意事項。

The installation of the membrane structure charging pile shed can prevent the charging pile from being exposed to the sun and rain, and extend its service life. In addition, the membrane structure parking shed can also bring convenience to people. When it rains heavily and is exposed to the sun, the canopy just provides a temporary shelter for the car. Today, I will introduce the installation steps and precautions of the charging pile shed.

安裝步驟：

Installation steps:

1、膜結構安裝時，應在膜面上安設爬用安全網，作業人員須系安全帶。在安裝過程中，作業人員在膜面上行走應穿軟底鞋，不應佩掛鑰匙等硬物。

1. When installing the membrane structure, the climbing safety net shall be installed on the membrane surface, and the operators must wear safety belts. During installation, operators shall wear soft soled shoes when walking on the membrane surface, and shall not wear hard objects such as keys.

2、膜結構的安裝宜在風力不大于四級的情況下進行。在安裝過程中應充分注意風速和風向，避免發生顫動現象。同時應根據降雨的程度決定工程的中止和繼續。

2. The installation of membrane structure should be carried out when the wind force is not greater than Grade IV. Pay full attention to the wind speed and direction during installation to avoid flutter. At the same time, the suspension and continuation of the project shall be determined according to the degree of rainfall.

3、張拉時應確定分批張拉順序、量值，控制張拉的速度，并根據材料的特性確定超張拉量值。

3. During tensioning, the tensioning sequence and quantity shall be determined in batches, the tensioning speed shall be controlled, and the over tensioning quantity shall be determined according to the characteristics of materials.

4、當下道工序或相鄰工程開始施工時，對膜結構已完成部分須采取保護措施，防止損壞。

4. When the next process or adjacent works start construction, protective measures must be taken for the completed part of the membrane structure to prevent damage.

5、膜體輔設過程中須做好成品保護，不應損壞膜面。膜面支承結構之間須設隔離層，不得直接接觸。

5. The finished products must be well protected during the auxiliary installation of the membrane body, and the membrane surface shall not be damaged. Isolation layer shall be set between membrane supporting structures, and direct contact is not allowed.

6、膜結構的脊索、谷索其錨頭的組裝須嚴格按膜結構車棚廠的工藝標準執行，脊索、谷索應張拉到位。對有控制要求的張力值應作施工記錄，對無控制要求的應作張拉行程記錄。

6. The assembly of the anchor head of the ridge cable and valley cable of the membrane structure must strictly comply with the process standards of the membrane structure shed factory, and the ridge cable and valley cable should be tensioned in place. The tension value with control requirements shall be recorded for construction, and the tensioning stroke without control requirements shall be recorded.

7、膜結構脊索、谷索的安裝應按施工組織設計要求進行。在膜結構安裝過程中在脊索、谷索安裝之前宜采用臨時脊、谷壓繩。以防止未完工膜結構在風載下產生過大晃動。

7. The installation of ridge cable and valley cable of membrane structure shall be carried out according to the requirements of construction organization design. During the installation of membrane structures, temporary ridge and valley pressing ropes should be used before the installation of ridge and valley cables. To prevent the unfinished membrane structure from excessive shaking under wind load.

注意事項：

matters needing attention:

1、膜結構充電樁車棚在建造前要進行實地考察，不僅要考慮停車方便，還得考慮施工方面的因素，綜合自然環境風力雨雪的影響，盡量選擇避開風口施工難度小的位置。

1. Before the construction of the membrane structure charging pile shed, the field investigation shall be carried out. Not only the convenience of parking, but also the factors of construction shall be considered. Considering the impact of wind, rain and snow in the natural environment, the location with less difficulty in construction shall be selected as far as possible to avoid the tuyere.

2、根據實地考察結果，設計合理的結構圖。膜結構充電樁車棚的設計非常重要，既要考慮充電樁的大小尺寸又得考慮環境天氣，如果風大雨雪大的地方盡量使用帶帽頂結構的設施，這樣可以充分緩解風雪的阻力和積雪融化后的處理。在風力小或者有折風墻的地方可以用直挑或者七字型膜結構車棚，這樣可以節省工程成本縮短施工工期。

2. According to the results of field investigation, a reasonable structure diagram is designed. The design of the membrane structure charging pile shed is very important. Both the size of the charging pile and the environmental weather should be considered. If the wind, rain and snow are heavy, try to use the facilities with a cap structure, which can fully alleviate the resistance of wind and snow and the treatment after snow melting. In places with low wind force or wind break walls, we can use straight cantilever or seven shaped membrane structure shed, which can save project cost and shorten construction period.

3、膜結構充電樁車棚膜材的選擇盡量用進口自潔性高的膜材。因為充電樁是耐耗工程這就要求膜結構充電樁停車棚使用壽命要持久，進口膜材可以提高整體使用壽命，并且拉力大抗風性高，非常的符合要求。

3. The membrane materials for the vehicle shed of the membrane structure charging pile shall be imported membrane materials with high self-cleaning property. Because the charging pile is a wear resistant project, it requires that the service life of the membrane structure charging pile parking shed should be long. Imported membrane materials can improve the overall service life, and the tension is large and the wind resistance is high, which is very consistent with the requirements.

建議，建造膜結構充電樁車棚要選擇經驗資質齊全的膜結構公司。因為有實際經驗，所以在圖紙的設計階段及車棚施工中對結構的細節處理，會非常的到位。更多相關內容就來我們網站http://www.jncx.com.cn咨詢吧。

It is suggested that membrane structure companies with complete experience and qualifications should be selected for the construction of membrane structure charging pile shed. Because of practical experience, the details of the structure will be handled in place during the design stage of the drawings and the construction of the shed. More relevant content will come to our website http://www.jncx.com.cn Consult.