景觀膜結構在安裝及使用過程中，經常會出現一些小問題，如安裝時在地面或其它構筑物上拖動的磨損、尖銳物體劃傷或刺破、膜材吊裝或張拉時的意外撕裂，使用過程中高空墜物擊破或人為破壞等等，而這些情況一旦發生，需及時處理的。下面山東膜結構廠家就來講講景觀膜結構膜面破損的處理方式。

In the process of installation and use of landscape membrane structures, some small problems often occur, such as wear caused by dragging on the ground or other structures during installation, scratches or punctures caused by sharp objects, accidental tears caused by lifting or tensioning of membrane materials, damage caused by falling objects or man-made damage during use, etc. Once these situations occur, they need to be handled in a timely manner. Next, Shandong membrane structure manufacturers will talk about the treatment of damage to the membrane surface of landscape membrane structures.

一、膜結構破損以及處理工作：

1、 Membrane structure damage and treatment:

1、如果僅僅是局部膜材的表面涂層磨損、基布織物的纖維完好，可用高性能透明膠粘貼或熱合在磨損區域。

1. If only the surface coating of local membrane material is worn, and the fiber of base cloth fabric is intact, high-performance transparent adhesive can be used to paste or heat seal in the worn area.

2、如果膜面破壞范圍長度小于50mm,剪一橢圓形或圓形膜布，作為補強層焊接在破壞區域的上面。

2. If the length of the damage area of the membrane surface is less than 50mm, cut an oval or round membrane cloth and weld it on the damaged area as a reinforcement layer.

3、如果膜面破壞范圍長度超過50mm但小于300mm,準備一長度和寬度比破壞范圍大150mm的膜條，作為補強層焊接在破壞區域的膜面上。

3. If the length of the damage range of the membrane surface exceeds 50mm but is less than 300mm, prepare a membrane strip whose length and width are 150mm larger than the damage range, and weld it on the membrane surface of the damage area as a reinforcement layer.

4、如果膜面破壞部分超過300mm長，需將整個破壞的單元拆下運回工廠修補或更換整個單元。

4. If the damaged part of the membrane surface is more than 300mm long, the entire damaged unit shall be removed and transported back to the factory for repair or replacement.

二、根據膜結構材料的不同，具體方法如下：

2、 According to different membrane structural materials, the specific methods are as follows:

1、PVC涂層覆蓋的膜材料可采用熱風機修補；將待補區域清理干凈、鋪放平整，補丁鋪在待焊面上，用熱風將膜材表面的PVC涂層融化，再將補丁與下層膜用小滾輪壓機使其牢固地連在一起。而上述1至3的情況是現場修補，具體修補方法隨所用膜材種類而定。

1. The membrane material covered by PVC coating can be repaired by hot air blower; Clean the area to be repaired, lay it flat, lay the patch on the surface to be welded, melt the PVC coating on the membrane surface with hot air, and then firmly connect the patch with the lower membrane with a small roller press. The above 1 to 3 cases are on-site repair, and the specific repair method depends on the type of membrane materials used.

2、對PTFE涂層覆蓋的膜材，需在補丁與原破壞的膜材間加一層氟化乙丙烯薄膜；再用專用手提焊接設備壓緊在補丁上，用高溫使氟化乙丙烯薄膜融化從而將補丁焊接在膜面上。具體操作時要注意加熱溫度和加熱時間的把握，既要使待焊膜材的表面涂層或FEP薄膜充分融化從而能牢固粘在一起，又要防止因過熱而燒焦膜材。

2. For the membrane material covered by PTFE coating, a layer of FEP film shall be added between the patch and the original damaged membrane material; Then press the patch with special portable welding equipment, melt the FEP film with high temperature, and weld the patch on the film surface. During specific operation, pay attention to the control of heating temperature and heating time, not only to fully melt the surface coating or FEP film of the film material to be welded so as to firmly stick together, but also to prevent the film material from burning due to overheating.

景觀膜結構膜面破損的處理方式以及其他內容的了解就講解到這里了，您對此有什么疑問要解答嗎？歡迎來我們網站http://www.jncx.com.cn咨詢了解！

This is the end of our understanding of how to deal with the damage of the membrane surface of the landscape membrane structure and other contents. Do you have any questions to answer? Welcome to our website http://www.jncx.com.cn Ask about it!